您好,欢迎您来到:金沙澳门登陆网站官网!服务热线:0512-62751429.
YUSH Electronic
资讯动态
多组多刀分板机的功能优势
多刀分板机的上刀片和下刀片形成一组以形成切割单元。他们分别是a、b、c和3组。整个切割过程分为三个阶段。甲组刀片先切割电路板的40%,然后乙组刀片再次运行在甲组刀片切割的凹槽上,再次完成40%的切割量。最后,C组刀片切割最后的20%并修剪。由于每次切削量小,与传统的一次性切削方法相比,切削过程中产生的应力减少了80%以上。分开的电路板的边缘是平坦和光滑的,并且板表面非常平坦,没有扭曲或翘曲。
The upper blade and the lower blade of the multi cutter splitter form a group to form a cutting unit. They were group A, group B, group C and group 3. The whole cutting process is divided into three stages. Group a blade first cuts 40% of the circuit board, and then group B blade runs again on the groove cut by group a blade to complete 40% cutting amount again. Finally, group C blades cut the last 20% and trim. Compared with the traditional one-off cutting method, the stress produced in the cutting process is reduced by more than 80% due to the small amount of cutting each time. The edges of the separated boards are flat and smooth, and the board surface is very flat without distortion or warpage.
多刀分板机可以一次分割整块板材,并且可以上下对接,实现无人操作。不仅安装方便,而且操作设置简单,可以节省很多员工、时间和人力。占用空间小,最大限度地节省了操作时间。多刀分板机可同时切割多组刀具,并一次分割整块板材,从而保证分离后的板材不变形,同时不翘曲,效率高,并严格控制变形程度。
The multi cutter board dividing machine can split the whole board at one time, and can be connected up and down to realize unmanned operation. It is not only easy to install, but also easy to set up, which can save a lot of staff, time and manpower. It takes less space and saves operation time to the greatest extent. The multi cutter dividing machine can cut multiple groups of cutting tools at the same time, and divide the whole plate at one time, so as to ensure that the separated plate does not deform and warpage at the same time, with high efficiency and strict control of deformation degree.
多刀分板机采用进口TBI螺杆,定位精度高,刀盘受力小。多刀分板机采用安全性能高的开门保护装置。多刀分板机可自动送料和切板,效率更高。上下对接纸板机,节省劳动力。多叶片分板机的叶片材料为进口高速钢。刀片与刀片正面之间的距离至少为3毫米,刀片厚度为0.2毫米,介子尺寸根据印刷电路板的尺寸定制,刀片的使用寿命为10万次,刀片可反复翻转研磨重复使用。根据具体情况,铲刀可以转动和打磨2-3次。
 The imported TBI screw is used in the multi cutter dividing machine, with high positioning accuracy and small force on the cutter head. The door opening protection device with high safety performance is adopted for the multi cutter board splitter. The machine can automatically feed and cut the plate with higher efficiency. Up and down docking paperboard machine, saving labor. The blade material of multi blade plate splitter is imported high speed steel. The distance between the blade and the front of the blade is at least 3mm, and the thickness of the blade is 0.2mm. The size of the meson is customized according to the size of the printed circuit board. The service life of the blade is 100000 times. The blade can be repeatedly overturned, ground and reused. According to the specific situation, the blade can be rotated and polished 2-3 times.
多刀分板机采用多组上、下刀片同时分断。设备底部安装有带可调脚杯的脚轮,方便设备移动,不移动时需要稳定固定。上刀和下刀之间的间隙可根据印刷电路板的V形切割间距进行调整,精度控制在0.1毫米,相邻两组刀片之间的间距可在10毫米至25毫米之间调整,所需宽度可快速调整。刀具开始运行,多组刀具同时切割产品,整块拼版一次分割,产品输送带开始运行。产品分割完成后,传送带马上停止,以确保产品停留在传送带上。
The multi knife plate splitter adopts multiple groups of upper and lower blades to break at the same time. A caster with adjustable foot cup is installed at the bottom of the equipment, which is convenient for the equipment to move. It needs to be fixed stably when it is not moved. The gap between the upper and lower blades can be adjusted according to the V-shaped cutting distance of printed circuit board. The precision is controlled within 0.1 mm. The distance between two adjacent groups of blades can be adjusted between 10 mm and 25 mm. The required width can be adjusted quickly. The tool starts to run, multiple sets of cutters cut the product at the same time, the whole block is divided at one time, and the product conveyor belt starts to run. The conveyor belt stops immediately after the product separation to ensure that the product stays on the conveyor belt.
上述所讲解的就是多刀分板机的功能优势,希翼看完能够对您有所帮助,如果您想要了解更多关于多刀分板机的功能优势,欢迎在线咨询客服或是拨打本企业服务热线(网站右上角)进行咨询,金沙澳门登陆网站将竭诚为您提供优质的服务!
The above explanation is the function advantages of the multi knife splitter. I hope it can help you after reading it. If you want to know more about the functional advantages of the multi cutter board splitter, please contact customer service online or call our service hotline (top right corner of the website) for consultation. We will wholeheartedly provide you with high-quality service!
产品分类

                                  多组多刀分板机的功能优势


                                  多刀分板机的上刀片和下刀片形成一组以形成切割单元。他们分别是a、b、c和3组。整个切割过程分为三个阶段。甲组刀片先切割电路板的40%,然后乙组刀片再次运行在甲组刀片切割的凹槽上,再次完成40%的切割量。最后,C组刀片切割最后的20%并修剪。由于每次切削量小,与传统的一次性切削方法相比,切削过程中产生的应力减少了80%以上。分开的电路板的边缘是平坦和光滑的,并且板表面非常平坦,没有扭曲或翘曲。
                                  The upper blade and the lower blade of the multi cutter splitter form a group to form a cutting unit. They were group A, group B, group C and group 3. The whole cutting process is divided into three stages. Group a blade first cuts 40% of the circuit board, and then group B blade runs again on the groove cut by group a blade to complete 40% cutting amount again. Finally, group C blades cut the last 20% and trim. Compared with the traditional one-off cutting method, the stress produced in the cutting process is reduced by more than 80% due to the small amount of cutting each time. The edges of the separated boards are flat and smooth, and the board surface is very flat without distortion or warpage.
                                  多刀分板机可以一次分割整块板材,并且可以上下对接,实现无人操作。不仅安装方便,而且操作设置简单,可以节省很多员工、时间和人力。占用空间小,最大限度地节省了操作时间。多刀分板机可同时切割多组刀具,并一次分割整块板材,从而保证分离后的板材不变形,同时不翘曲,效率高,并严格控制变形程度。
                                  The multi cutter board dividing machine can split the whole board at one time, and can be connected up and down to realize unmanned operation. It is not only easy to install, but also easy to set up, which can save a lot of staff, time and manpower. It takes less space and saves operation time to the greatest extent. The multi cutter dividing machine can cut multiple groups of cutting tools at the same time, and divide the whole plate at one time, so as to ensure that the separated plate does not deform and warpage at the same time, with high efficiency and strict control of deformation degree.
                                  多刀分板机采用进口TBI螺杆,定位精度高,刀盘受力小。多刀分板机采用安全性能高的开门保护装置。多刀分板机可自动送料和切板,效率更高。上下对接纸板机,节省劳动力。多叶片分板机的叶片材料为进口高速钢。刀片与刀片正面之间的距离至少为3毫米,刀片厚度为0.2毫米,介子尺寸根据印刷电路板的尺寸定制,刀片的使用寿命为10万次,刀片可反复翻转研磨重复使用。根据具体情况,铲刀可以转动和打磨2-3次。
                                   The imported TBI screw is used in the multi cutter dividing machine, with high positioning accuracy and small force on the cutter head. The door opening protection device with high safety performance is adopted for the multi cutter board splitter. The machine can automatically feed and cut the plate with higher efficiency. Up and down docking paperboard machine, saving labor. The blade material of multi blade plate splitter is imported high speed steel. The distance between the blade and the front of the blade is at least 3mm, and the thickness of the blade is 0.2mm. The size of the meson is customized according to the size of the printed circuit board. The service life of the blade is 100000 times. The blade can be repeatedly overturned, ground and reused. According to the specific situation, the blade can be rotated and polished 2-3 times.
                                  多刀分板机采用多组上、下刀片同时分断。设备底部安装有带可调脚杯的脚轮,方便设备移动,不移动时需要稳定固定。上刀和下刀之间的间隙可根据印刷电路板的V形切割间距进行调整,精度控制在0.1毫米,相邻两组刀片之间的间距可在10毫米至25毫米之间调整,所需宽度可快速调整。刀具开始运行,多组刀具同时切割产品,整块拼版一次分割,产品输送带开始运行。产品分割完成后,传送带马上停止,以确保产品停留在传送带上。
                                  The multi knife plate splitter adopts multiple groups of upper and lower blades to break at the same time. A caster with adjustable foot cup is installed at the bottom of the equipment, which is convenient for the equipment to move. It needs to be fixed stably when it is not moved. The gap between the upper and lower blades can be adjusted according to the V-shaped cutting distance of printed circuit board. The precision is controlled within 0.1 mm. The distance between two adjacent groups of blades can be adjusted between 10 mm and 25 mm. The required width can be adjusted quickly. The tool starts to run, multiple sets of cutters cut the product at the same time, the whole block is divided at one time, and the product conveyor belt starts to run. The conveyor belt stops immediately after the product separation to ensure that the product stays on the conveyor belt.
                                  上述所讲解的就是多刀分板机的功能优势,希翼看完能够对您有所帮助,如果您想要了解更多关于多刀分板机的功能优势,欢迎在线咨询客服或是拨打本企业服务热线(网站右上角)进行咨询,金沙澳门登陆网站将竭诚为您提供优质的服务!
                                  The above explanation is the function advantages of the multi knife splitter. I hope it can help you after reading it. If you want to know more about the functional advantages of the multi cutter board splitter, please contact customer service online or call our service hotline (top right corner of the website) for consultation. We will wholeheartedly provide you with high-quality service!
                                  金沙澳门登陆网站 版权所有 @ Copyright 2015 联系人:刘小姐 地址:江苏省苏州市昆山市金阳东路1068号G栋厂房, 分板机宇顺力专业生产V-CUT分板机|电路板分板机|邮票孔分板机|pcb气动分板机|分板机厂家|线路板分板机|冲压分板机|铡刀分板机|PCB数控分板机|PCB曲线分板机|上海分板机|分板机刀具|分板机配件|FPC冲床分板机|LED铝基板分板机。《中华人民共和国电信与信息服务业务经营许可证》编号:苏ICP备14049770号-4
                                  联系金沙澳门登陆网站
                                  分板机华南地址:
                                  分板机地址:广东省东莞市涌头村山泉路十号(总部)
                                  分板机咨询:13862072520
                                  分板机电话:0769-88087410
                                  分板机网址:
                                  华东分板机地址:
                                  分板机地址:江苏省苏州市昆山市金阳东路1068号(国瑞产业园)
                                  分板机电话:0512-62751429
                                  咨询分板机:13450659407
                                  分板机邮箱:evaliu@hk-yush.com
                                  分板机网址:http://www.yushunli.com
                                  金沙澳门登陆网站 版权所有 @ Copyright 2015 联系人:刘小姐 地址:江苏省苏州市昆山市金阳东路1068号G栋厂房, 分板机宇顺力专业生产V-CUT分板机|电路板分板机|邮票孔分板机|pcb气动分板机|分板机厂家|线路板分板机|冲压分板机|铡刀分板机|PCB数控分板机|PCB曲线分板机|上海分板机|分板机刀具|分板机配件|FPC冲床分板机|LED铝基板分板机。《中华人民共和国电信与信息服务业务经营许可证》编号:苏ICP备14049770号-4
                                  XML 地图 | Sitemap 地图